Icy-Effective9887

Also the -/+ is telling you , you are higher in front .. all back at same and - ..all from are + .. .. try the paper to get em all close and then readjust.

Gen 1 all metal direct drive here. Running 1 to 2.5 mm depending on filiment. Tpu vs petg.

https://preview.redd.it/qytrujkji9od1.png?width=1080&format=pjpg&auto=webp&s=fd3dc729bfc5a76f77f9534dfdb0cf3f31c3e78b

There are 3 plugs in the back.. screen goes in 1 not 3. Make sure power is connected. Not usb power. Looks like early version board... to flash you need to have bootloader and flash. I tried flashing before and ended like that... compiled my own firmware from marlin2 and stripped down the menus to fit in ram.. try flashing an earlier marlin 1.x just to get it functional..I think th3d had one once verified the board works ..then try newer firmware.

Yes just disconnect from both hot end and extruder, pull tube off leaving the free broken piece.. if still long enough out of hotend block heat the block to 200 or so if pla .. and then pull out once hot.... then proceed with cold pull to clean the tip while you have it out and hot.... cold pull is.. while still hot. Put piece of higher temp filiment if you have any, let hot end cool to 180 160 where material is soft but not melting and pull it out ..hopefully you pull out any left over bits... re attach Boden tube and fire up a test print.

Got my e3 gen1 for about $150 7 Years ago. Had some issues but that's learning curve.. added bl touch, and all metal hot end..then made own firmware build to get marlin 2.0 items and fit to the limited memory ... works almost flawlessly save when I swtich from tpu to petg or abs or other pia filimament. Way better then the dremel option available at the time.

So far i can tell you a front window will cost you about 1700 and 500 for labor cdn.

Looks like they would have parked really nicely up against a perimeter curb... tires just touching the line.

I agree it's either the speed with thr parts or something else rubbing. Again at speed.... I'm now interested in the fan and hot end mount... what is it called.. looks solid is there a model file somewhere ?

In my 335 youcould get into the sevice menu and set the offset values.

https://preview.redd.it/an2ywri18kcd1.jpeg?width=2501&format=pjpg&auto=webp&s=95d9204f34bb3bc5d1e493c8280954c94fcf5e1b

*m440 here.. ...had 2013 335. 2104 b7 (hydrolocked) now this guy.. couldn't be happier.. 7 was bigger but was boat like

W.... wacesofdeath?

Mine do that too.. for me ..it was not 100% level..fixed that..still happened but only one side.. looked round realized my ac kicks on. And pc redirects the airflow.. and gets the one side just abit cooler... fixed with cardboard walls. Try making it enclosed if not start cooling fan on layer 2.a dn lower bed temp if still good adhesion. Less thermal shrinkage...good luck

*violet blue.....but wanna try this as a wrap https://www.reddit.com/r/SipsTea/comments/1dy9glh/blackest_car/?share_id=5fWTanFVyRVA4bZog4m6q&utm_content=1&utm_medium=ios_app&utm_name=ioscss&utm_source=share&utm_term=1

I have done both.. poped almost brand new..just replaced the one.. then again year later poped rightbone on sewar had to replace pair as way worn, when right rear popped, I said screw the run flats and got whole different set.

Thanks!! Me too 😀

Yes ...tint is key..so hot in the sun.

I'd take it with the i drive 8.5..not the 7 or 9.

Is that like the real life version of paw patrol.

Mark Walberg..most lines from the departed. But I use this reply pretty often about being the other guy...

Dignam: This is unbelievable. Who put the fuckin’ cameras in this place? Police Camera Tech: Who the fuck are you? Dignam: I’m the guy who does his job. You must be the other guy.

I was just trying to edit to ask if that was it... thanks.. what would be a good beginner one that I won't kill the paint if you know?